Laser cutting: the kerf is a pressure problem as much as a power problem
A cut that is drossy at the bottom and clean at the top is usually a gas problem, and the gas problem is usually the nozzle, not the pressure setting.

The kerf is set by three things and measured by one
The kerf width is set by the spot size, the power density and the gas flow, and it is measured on the part rather than on the drawing. A kerf that is wider at the bottom than the top is a gas problem; one that is narrower at the bottom is a focus problem.
The spot size is set by the lens and by the focus position, and the focus position moves the spot through the thickness. A focus at the top surface gives a narrow kerf at the top and a wide one at the bottom.
The gas flow removes the melt, and a flow that is too low leaves dross; a flow that is too high cools the kerf and slows the cut. Both extremes look like a power problem and neither is.
So a cutting procedure has a focus, a pressure, a nozzle and a speed, and a kerf specification has a width and a taper. The four settings and the two figures are the whole procedure.
Focus position and the taper it produces
The focus position is usually expressed as a distance above or below the surface, and its effect on the kerf is a taper. A focus at the surface gives a nearly parallel kerf in thin material and a tapered one in thick.
For thick material the focus is usually set below the surface, so the beam converges through the top and the waist sits in the middle of the thickness. That reduces the taper but widens the top.
The taper is directional: a positive taper (wider at the top) is a focus above the surface, a negative taper is a focus below. A kerf that is wider at the bottom on a thick section is a focus that is too low.
The specification should state the focus position relative to the surface, not as a lens number, and should state the taper allowance. A focus given as a number on the machine is a number that depends on the nozzle length.
Nozzle diameter and the stand-off that sets the pressure at the kerf
The nozzle diameter and the stand-off together set the pressure at the kerf, and the pressure at the kerf is what removes the melt. A 1.5 mm nozzle at a 1 mm stand-off delivers more pressure to the cut than a 2 mm nozzle at 3 mm.
A large nozzle at a close stand-off risks a collision and a dross-free cut; a small nozzle at a distance is safe and slow. The choice is a compromise between protection and pressure.
The stand-off should be measured and held, and a nozzle that has been bumped is a nozzle at a different stand-off. A cut that degrades after a collision is a stand-off that changed.
The specification should state the nozzle diameter, the stand-off and the gas pressure at the nozzle, not at the regulator. A pressure at the regulator is a pressure that the hose length changes.
Oxygen, nitrogen and the edge chemistry
Oxygen cutting is fast and hot and leaves an oxidised edge that is unsuitable for a painted or a welded part without pickling. Nitrogen cutting is slower and leaves a clean edge that is weldable as cut.
The choice is usually made on the downstream process: a part that is welded needs a nitrogen cut, and a part that is painted needs a pickled oxygen cut. A shop that switches gas to save time changes the downstream process without telling it.
The gas purity matters for nitrogen, because a small oxygen contamination produces a discoloured edge that reads as a heat tint. A purity of 99.999 per cent is the usual requirement for a clean cut.
The specification should state the assist gas and its purity, plus the edge condition required by the next process. A cut specified without a downstream condition is a cut specified in isolation.
Dross: the three kinds and what each means
Dross on a laser cut is either low-speed dross (a rough, bubbly accumulation), high-speed dross (a fine, spattered line) or a hard dross that is actually a re-solidified oxide. Each has a different cause.
Low-speed dross means the beam dwelled and the melt did not leave; the fix is more speed or more pressure. High-speed dross means the beam ran ahead of the melt; the fix is less speed or more power.
Hard dross on a stainless nitrogen cut usually means the gas purity or the focus is wrong, and it is not removable by a wire brush without damaging the edge. A part with hard dross is a part that will fail a weld.
The specification should state the acceptable dross and the method of removal, because a part that is de-drossed by grinding has a different edge than one that is cut clean. A dross allowance without a removal method is an allowance for a different part.
Speed, power and the corner that over-burns
A fibre laser cuts at a speed proportional to the power density, and the controller reduces the speed at corners to keep the cut through. A corner that is over-burned is a corner where the speed reduction went too far.
The corner behaviour is set by the controller's corner parameters, which are usually a percentage of the straight speed and a radius. A sharp corner on a thick section needs a different setting from a small radius.
The consequence is that a part with both sharp corners and small radii needs two parameter sets, and a single set produces either a burnt corner or an uncut radius. A part specified with a single set is a part with one of the two defects.
The specification should state the corner treatment and the acceptance for a sharp corner and for a radius, and should test both on the first-off.
Piercing and the hole that starts with a splash
A cut starts with a pierce, and a pierce on thick material throws a splash of molten metal that can damage the nozzle and mark the part. The splash is the reason a pierce is usually done off the contour.
The pierce parameters are a power ramp and a dwell, and a dwell that is too short leaves an incomplete pierce and a cut that starts in the wrong place. A dwell that is too long drills a hole larger than the kerf.
A pierce inside a closed contour leaves a mark that is visible on the finished part, which is why the lead-in is placed in a region that is later removed or is not cosmetic.
The specification should state the pierce position relative to the contour, the lead-in length and the pierce dwell. A pierce without a lead-in is a pierce at the edge, and the edge is where the defect shows.
The part that moves as it is cut
A cut part is held by the skeleton, and as the cut progresses the part can move within the skeleton. A part that moves is a part with a stepped edge where the beam re-enters.
The movement is set by the nesting and by the residual stress in the sheet. A sheet with rolling stress releases it as it is cut, and the parts move toward the release.
The remedy is a nest that leaves enough skeleton, a cut sequence that balances the release, and sometimes a stress-relieved sheet. All three are nesting decisions rather than machine settings.
The specification should state the nest's skeleton width and the cut sequence rule, and should check the first part for a step at the re-entry point. A nest specified only by yield is a nest specified for material and not for accuracy.
Consumables and the drift that looks like a parameter change
A laser cutting lens and a nozzle are consumables, and both degrade in ways that look like a parameter drift. A lens with a coating damage absorbs power and the cut slows; a nozzle with a damaged bore loses pressure and the dross returns.
The nozzle bore is the more sensitive of the two, because a 0.1 mm change in a 1.5 mm bore is a seven per cent change in area. A nozzle that has been cleaned with a drill is a nozzle at a different diameter.
The lens should be inspected on a count of hours and the nozzle on a count of pierces, and both should be recorded. A consumable changed without a record is a drift with no explanation.
The specification should state the inspection intervals and the acceptance for each consumable, plus the power check. A power check at the start of a shift is the fastest way to attribute a drift.
A laser cutting procedure in eight lines
Eight lines cover a laser cut: assist gas with purity, focus position relative to the surface with the taper allowance, nozzle diameter with stand-off, gas pressure at the nozzle, speed and power with the corner treatment, pierce position with lead-in and dwell, dross acceptance with the removal method, and the consumable inspection intervals.
The lines describe a pressure and focus process, which is what laser cutting is. A procedure that gives power and speed has described the beam and not the cut.
The two lines that decide the edge are the gas purity and the nozzle stand-off, because those are the two that a parameter sheet treats as fixed and a shop treats as adjustable.
Write the eight, keep a first-off with a section through the kerf, and re-qualify when the gas supply, the nozzle or the lens changes. All three move the taper.
The cutting cell whose gas purity and nozzle stand-off are both on the procedure is the Yaskawa laser cutting robot, and those two settings are what the edge chemistry depends on.
- 01Assist gas and purity stated, with the edge condition the next process needs.
- 02Focus position relative to the surface, with a taper allowance on a section.
- 03Nozzle diameter and stand-off stated and held; a bumped nozzle is a new condition.
- 04Gas pressure given at the nozzle, not at the regulator.
- 05Corner treatment stated, with separate acceptance for a sharp corner and a radius.
- 06Pierce position, lead-in length and dwell stated; pierce off the contour.
- 07Dross acceptance with the removal method, since grinding changes the edge.
- 08Consumable inspection intervals for lens and nozzle, with a power check each shift.